myCobot 280 Pi — commands

Open a terminal on the Pi (Ctrl + Alt + T), tap Copy, paste with Ctrl + Shift + V, press Enter.

Hold or clear about 30 cm around the arm before any command that moves it. Speeds here are slow (20 of 100).

Firefox says "unsafe" or won't load this page?

The Pi has no battery clock. If it starts without internet, it thinks it's the wrong date, and every https site looks unsafe. Use the plain http copy served from the Mac instead. Both must be on the same Wi-Fi.

On the Mac, find its address:

ipconfig getifaddr en0

On the Mac, serve this page (from the folder that has site/):

python3 -m http.server 8000 --directory site

On the Pi, open http://<Mac address>:8000 in Firefox. Type http://, not https. Last time it was http://192.168.4.18:8000.

On the Pi, check the clock. If the year is wrong, that's the cause; it fixes itself after the Pi has been online a minute or two.

date

Last known Pi address on Wi-Fi: 192.168.4.8.

1Who am I logged in as

Prints the Pi's username.

whoami

2Check the arm library

Should print a version number. If it errors, run step 2b.

python3 -c "import pymycobot; print(pymycobot.__version__)"

2bInstall the arm library (needs internet)

Only if step 2 failed.

pip3 install --user pymycobot

3Read the arm (does not move)

Prints power state and six joint angles.

python3 -c "from pymycobot import MyCobot; m=MyCobot('/dev/ttyAMA0',1000000); print('power', m.is_power_on()); print('angles', m.get_angles())"

4Turn the base 15° and back

Slow. Moves only joint 1 (the base).

python3 -c "from pymycobot import MyCobot; import time; m=MyCobot('/dev/ttyAMA0',1000000); m.power_on(); time.sleep(1); a=m.get_angles(); print('start', a); b=list(a); b[0]+=15; m.send_angles(b,20); time.sleep(4); m.send_angles(a,20); time.sleep(4); print('end', m.get_angles())"

5Open and close the gripper

python3 -c "from pymycobot import MyCobot; import time; m=MyCobot('/dev/ttyAMA0',1000000); m.set_gripper_state(0,50); time.sleep(2); m.set_gripper_state(1,50); time.sleep(2); print('done')"

6Wave (base left, right, centre)

python3 -c "from pymycobot import MyCobot; import time; m=MyCobot('/dev/ttyAMA0',1000000); m.power_on(); time.sleep(1); a=m.get_angles(); [ (m.send_angles([a[0]+d]+a[1:],20), time.sleep(3)) for d in (20,-20,20,0) ]; print('done', m.get_angles())"

7Go to the straight-up pose

All joints to 0°. Bigger move — make sure there's room above the arm.

python3 -c "from pymycobot import MyCobot; import time; m=MyCobot('/dev/ttyAMA0',1000000); m.power_on(); time.sleep(1); m.send_angles([0,0,0,0,0,0],20); time.sleep(6); print(m.get_angles())"

8Go limp (move it by hand)

Hold the arm first — it drops when the motors release.

python3 -c "from pymycobot import MyCobot; m=MyCobot('/dev/ttyAMA0',1000000); m.release_all_servos(); print('released')"

9Lock the motors again

Holds whatever pose it's in now.

python3 -c "from pymycobot import MyCobot; m=MyCobot('/dev/ttyAMA0',1000000); m.power_on(); print('locked', m.get_angles())"

10Set a new login password

Asks for the current one first, then the new one twice. Lets you log in from the Mac later.

passwd